| Discussion Forum: All Replies to Message 1467776 |
|
 |
| | | Author: | macebobo  | | Posted: | May 3, 2024 15:20 | | Subject: | Re: Damaged part due to new box? | | Viewed: | 53 times | | Topic: | LEGO products | |
|
| In LEGO products, Dhobeck writes:
| | I was going to keep all of the collectible minifigures series 26 sealed but seeing this. Im going back to opening them up. I think I found the source of the damage. 2x3 tile after rubbing it against the instructions
|
So, do you believe it is the ink from the instructions? Do you feel it is possible
to be cleaned off without damaging the printing?
|
|
| | | | | |
| | | | | Author: | Dhobeck | | Posted: | May 3, 2024 15:44 | | Subject: | Re: Damaged part due to new box? | | Viewed: | 56 times | | Topic: | LEGO products | |
|
| In LEGO products, macebobo writes:
| | In LEGO products, Dhobeck writes:
| | I was going to keep all of the collectible minifigures series 26 sealed but seeing this. Im going back to opening them up. I think I found the source of the damage. 2x3 tile after rubbing it against the instructions
|
So, do you believe it is the ink from the instructions? Do you feel it is possible
to be cleaned off without damaging the printing?
|
Tested on tile and while I could remove some most of it was still there after
10ish minutes of erasing/rubbing. With that in mind I might be able to but at
that point I would have to list it as used and put a warning on it
|
|
| | | | | | | | | |
| | | | | | | Author: | Saitobricks.ca | | Posted: | May 3, 2024 15:49 | | Subject: | Re: Damaged part due to new box? | | Viewed: | 35 times | | Topic: | LEGO products | |
|
| In LEGO products, Dhobeck writes:
| | In LEGO products, macebobo writes:
| | In LEGO products, Dhobeck writes:
| | I was going to keep all of the collectible minifigures series 26 sealed but seeing this. Im going back to opening them up. I think I found the source of the damage. 2x3 tile after rubbing it against the instructions
|
So, do you believe it is the ink from the instructions? Do you feel it is possible
to be cleaned off without damaging the printing?
|
Tested on tile and while I could remove some most of it was still there after
10ish minutes of erasing/rubbing. With that in mind I might be able to but at
that point I would have to list it as used and put a warning on it
|
|
|
| | | | | | | | | |
| | | | | | | Author: | macebobo | | Posted: | May 3, 2024 16:22 | | Subject: | Re: Damaged part due to new box? | | Viewed: | 46 times | | Topic: | LEGO products | |
|
| In LEGO products, Dhobeck writes:
| | In LEGO products, macebobo writes:
Tested on tile and while I could remove some most of it was still there after
10ish minutes of erasing/rubbing. With that in mind I might be able to but at
that point I would have to list it as used and put a warning on it
|
This is really unfortunate. I wonder if the change in packaging has anything
to do with this. Poly bags really didn't allow for much jostling, the boxes
seem to rattle quite a bit.
Thank you for posting your results here.
Also, it is refreshing to see a new seller so conscientious about doing things
correctly. Keep up the good work and never stop learning.
|
|
| | | | | | | | | | | | | |
| | | | | | | | | Author: | Dhobeck | | Posted: | May 3, 2024 17:04 | | Subject: | Re: Damaged part due to new box? | | Viewed: | 56 times | | Topic: | LEGO products | |
|
| In LEGO products, macebobo writes:
| | In LEGO products, Dhobeck writes:
| | In LEGO products, macebobo writes:
Tested on tile and while I could remove some most of it was still there after
10ish minutes of erasing/rubbing. With that in mind I might be able to but at
that point I would have to list it as used and put a warning on it
|
This is really unfortunate. I wonder if the change in packaging has anything
to do with this. Poly bags really didn't allow for much jostling, the boxes
seem to rattle quite a bit.
Thank you for posting your results here.
Also, it is refreshing to see a new seller so conscientious about doing things
correctly. Keep up the good work and never stop learning.
|
I do my best. I’ll be contacting Lego sometime later today though and we’ll see
what happens
|
|
|
|
|
|
|
USA, Oregon
Canada, Ontario